Wuxi, China · Manufacturer & exporter since 2016info@jcpipeline.com+86 18130056225
Home Products
Product ranges
Hot Tapping Machines Projects News About Contact
Home/Products/Hot Tapping Machines/Electric Hot Tapping Machines/Electric Hot Tapping Machine JC-E300
Electric Hot Tapping Machine JC-E300
05 · JC-E300

Electric Hot Tapping Machine JC-E300

Electric Hot Tapping Machine JC-E300 cuts branches from DN100 – DN300 (4" – 12") into live mains up to 16 bar. A 1.5 kW motor at 220 / 380 V / 50 Hz runs the bar at 40 r/min, and the manual feed advances the cutter at 3 mm/r; one hole takes 8 – 30 min. Travel is 600 / 700 mm, so a standard gate valve and tapping adapter fit above the pipe. The machine mounts on a flange connection and weighs 65 kg.

Key features

  • Working pressure ≤ 16 bar (PN16)
  • Tapping range DN100 – DN300
  • 600 / 700 mm boring bar travel
  • 1.5 kW motor, 220 / 380 V, 50 Hz, 40 r/min
  • Feed 3 mm/r, 8 – 30 min per hole
  • Flange connection, BS or ASME
  • Rated for water, oil, gas and steam

Lead time 25–35 working days after deposit. Test record, drawing and packing list go with every shipment. Payment: 30% T/T deposit, balance against copy of B/L.

Specifications

Tapping range4" – 12" (DN100 – DN300)
Tapping sizes4", 6", 8", 10", 12" (DN100, DN150, DN200, DN250, DN300)
Working pressure≤ 16 bar (PN16 / 232 psi)
Working temperatureup to +200 °C
Boring bar travel600 / 700 mm
Spindle speed40 r/min
Feed modeManual
Feed volume3 mm/r
Tapping time8 – 30 min per hole
Drive modeElectric motor
Motor power1.5 kW
Motor voltage220 / 380 V
Frequency50 Hz
Connection to valveFlange
Flange standardBS or ASME
Pipe mediumWater, oil, gas and steam
Pipe materialSteel, cast iron, plastic and concrete pipe
Dimensions1080 × 360 × 430 mm
Weight65 kg

Typical applications

Transmission and trunk mainsPower plant cooling-water headersIndustrial process pipingDistrict water and fire mainsDistrict heating primary mains
Product details

Overview

Electric Hot Tapping Machine JC-E300 cuts branches from DN100 – DN300 (4" – 12") into live mains up to 16 bar. A 1.5 kW motor at 220 / 380 V / 50 Hz runs the bar at 40 r/min, and the manual feed advances the cutter at 3 mm/r; one hole takes 8 – 30 min. Travel is 600 / 700 mm, so a standard gate valve and tapping adapter fit above the pipe. The machine mounts on a flange connection and weighs 65 kg.

One machine spans four tapping sizes from DN100 to DN300, which is why depots standardise on it instead of holding three separate units.

Models are listed with the flange pattern they are built to: BS or ASME.

Tapping sequence

  1. Fit the tapping saddle or flange to the pipe and pressure-test the branch.
  2. Bolt the valve and the machine to the connection; check the bar is square to the pipe.
  3. Fit the pilot bit and shell cutter matched to the pipe material, then open the valve.
  4. Advance at 3 mm/r; the pilot bit centres the hole and the cutter follows through.
  5. Retract the bar, close the valve and remove the machine; the branch is ready to pipe up.

Standard scope of supply

  • Hot tapping machine JC-E300, assembled and run-tested
  • Boring bar, 600 / 700 mm travel
  • Tapping adaptor to BS or ASME flange
  • Motor 1.5 kW, 220 / 380 V, 50 Hz with control box
  • Tool kit, seals and operating manual

Before you order

  • Pipe outside diameter, wall thickness and material (steel, cast iron, PE or concrete)
  • Working pressure and medium temperature
  • Flange standard and tapping size required — DN100, DN150, DN200, DN250, DN300
  • Cutter type: shell cutter for steel, carbide or diamond for cast iron and concrete
Model range

All models, side by side

ModelTapping range (inch)Tapping range (mm)DriveFeedFeed volume (mm/r)Boring bar travel (mm)Spindle speed (rpm)Motor power (kW)Motor voltage (V)Tapping time (min)Working pressure
JC-M503/4" – 2"DN20 – DN50ManualManual0.15 – 0.2240 / 350———10 – 20≤ 16 bar
JC-DM501/2" – 2"DN15 – DN50Cordless drillManual—3401,300——3 – 10≤ 16 bar
JC-E1002-1/2" – 4"DN65 – DN100ElectricManual3370531.1 / 1.5220 / 3808 – 20≤ 16 bar
JC-E2004" – 8"DN100 – DN200ElectricManual3500401.5220 / 3808 – 20≤ 16 bar
JC-E3004" – 12"DN100 – DN300ElectricManual3600 / 700401.5220 / 3808 – 30≤ 16 bar
JC-E40010" – 16"DN250 – DN400ElectricManual3600 / 800301.538015 – 40≤ 16 bar
JC-E50012" – 20"DN300 – DN500ElectricManual3800302.238025 – 50≤ 16 bar
JC-E60020" – 24"DN500 – DN600ElectricManual0.05 – 0.1900 / 110025438030 – 60≤ 16 bar
JC-E800-160032" – 64"DN700 – DN1600ElectricManual0.1 – 0.1516001011380100 – 240≤ 16 bar

Swipe the table sideways to see every column.

Dimensions and weights are nominal. Pressure ratings are working pressure at ambient temperature; confirm the flange standard and pipe material before ordering.

Related products

Other products in this range

Tell us the pipe, pressure and medium

Send the diameter, working pressure and what flows inside. We reply with a specification and price within one working day.

Send an inquiry →
WeChat Scan to add on WeChat JC-Leon
+86 18130056225